AMD Spansion S29AL004D55TFI02 4 Mbit CMOS 3V Boot Sector Flash Memory TSOP-48

Description

AMD Spansion S29AL004D55TFI02 4 Mbit CMOS 3V Boot Sector Flash Memory TSOP-48
The S29AL004D is a 4 Mbit, 3.0 volt-only Flash memory organized as 524,288 bytes or 262,144 words. The device is offered in 48-ball FBGA, 44-pin SO, and 48-pin TSOP packages. The word-wide data (x16) appears on DQ15–DQ0; the byte-wide (x8) data appears on DQ7–DQ0. This device requires only a single, 3.0 volt VCC supply to perform read, program, and erase operations. A standard EPROM programmer can also be used to program and erase the device. This device is manufactured using Spansion’s 200 nm process technology, and offers all the features and benefits of the Am29LV400B and MBM29LV400T/BC, which were manufactured using 320 nm process technology. The standard device offers access times of 70 and 90 ns, allowing high speed microprocessors to operate without wait states. To eliminate bus contention the device has separate chip enable (CE#), write enable (WE#) and output enable (OE#) controls. The device requires only a single 3.0 volt power supply for both read and write functions. Internally generated and regulated voltages are provided for the program and erase operations. The device is entirely command set compatible with the JEDEC single-power-supply Flash standard. Commands are written to the command register using standard microprocessor write timings. Register contents serve as input to an internal state-machine that controls the erase and programming circuitry. Write cycles also internally latch addresses and data needed for the programming and erase operations. Reading data out of the device is similar to reading from other Flash or EPROM devices. Device programming occurs by executing the program command sequence. This initiates the Embedded Program algorithm—an internal algorithm that automatically times the program pulse widths and verifies proper cell margin. The Unlock Bypass mode facilitates faster programming times by requiring only two write cycles to program data instead of four. Device erasure occurs by executing the erase command sequence. This initiates the Embedded Erase algorithm—an internal algorithm that automatically preprograms the array (if it is not already programmed) before executing the erase operation. During erase, the device automatically times the erase pulse widths and verifies proper cell margin. The host system can detect whether a program or erase operation is complete by observing the RY/BY# pin, or by reading the DQ7 (Data# Polling) and DQ6 (toggle) status bits. After a program or erase cycle is completed, the device is ready to read array data or accept another command. The sector erase architecture allows memory sectors to be erased and reprogrammed without affecting the data contents of other sectors. The device is fully erased when shipped from the factory. Hardware data protection measures include a low VCC detector that automatically inhibits write operations during power transitions. The hardware sector protection feature disables both program and erase operations in any combination of the sectors of memory. This can be achieved in-system or via programming equipment. The Erase Suspend feature enables the user to put erase on hold for any period of time to read data from, or program data to, any sector that is not selected for erasure. True background erase can thus be achieved. The hardware RESET# pin terminates any operation in progress and resets the internal state machine to reading array data. The RESET# pin may be tied to the system reset circuitry. A system reset would thus also reset the device, enabling the system microprocessor to read the boot-up firmware from the Flash memory. The device offers two power-saving features. When addresses are stable for a specified amount of time, the device enters the automatic sleep mode. The system can also place the device into the standby mode. Power consumption is greatly reduced in both these modes. Spansion’s Flash technology combines years of Flash memory manufacturing experience to produce the highest levels of quality, reliability and cost effectiveness. The device electrically erases all bits within a sector simultaneously via Fowler-Nordheim tunneling. The data is programmed using hot electron injection.
SPECIFICATIONS
Manufacturer: AMD Spansion
Part Number: S29AL004D55TFI02
Architectural Advantages
Single Power Supply Operation
– 2.7 to 3.6 volt read and write operations for battery-powered applications
Manufactured on 200 nm Process Technology
– Compatible with 0.32 μm Am29LV400B and MBM29LV400T/BC
Flexible Sector Architecture
– One 16 Kbyte, two 8 Kbyte, one 32 Kbyte, and seven 64 Kbyte sectors (byte mode)
– One 8 Kword, two 4 Kword, one 16 Kword, and seven 32 Kword sectors (word mode)
– Supports full chip erase
Unlock Bypass Program Command
– Reduces overall programming time when issuing multiple program command sequences
Top or Bottom Boot Block Configurations Available
Embedded Algorithms
– Embedded Erase algorithm automatically preprograms and erases the entire chip or any combination of designated sectors
– Embedded Program algorithm automatically writes and verifies data at specified addresses
Compatibility with JEDEC Standards
– Pinout and software compatible with single-power supply Flash
– Superior inadvertent write protection
Sector Protection Features
– A hardware method of locking a sector to prevent any program or erase operations within that sector
– Sectors can be locked in-system or via programming equipment
– Temporary Sector Unprotect feature allows code changes in previously locked sectors
Performance Characteristics
High Performance
– Access times as fast as 55 ns
– Extended temperature range (-40°C to +125°C)
Ultra-low Power Consumption (typical values at 5 MHz)
– 200 nA Automatic Sleep mode current
– 200 nA standby mode current
– 9 mA read current
– 20 mA program/erase current
Cycling Endurance: 1,000,000 cycles per sector typical
Data Retention: 20 years typical
Software Features
Data# Polling and Toggle Bits
– Provides a software method of detecting program or erase operation completion
Erase Suspend/Erase Resume
– Suspends an erase operation to read data from, or program data to, a sector that is not being erased, then resumes the erase operation
Hardware Features
Ready/Busy# Pin (RY/BY#)
– Provides a hardware method of detecting program or erase cycle completion
Hardware Reset Pin (RESET#)
– Hardware method to reset the device to reading array data
We are a
U.S. COMPANY
in business since 1995 and offer
FAST SHIPPING
, usually within 1 business day.
Our listings are for
GENUINE Items
, not cheap knock-off counterfeits.
Please view all photos for potential datasheets
and other information.
For full datasheet, please contact us.
Make sure to view the rest of our auctions for other
Electronic Components and Unique Electronic Devices
we have created.
Click on
Save This Seller
and get notified of Sales and New Product Listings.
If you want to purchase more quantity than listed or don't see the exact item you are searching for, please ask, we are here to help you.  We offer a discount on multiple item purchases and / or large quantities.