Cypress Spansion S29AL016J70TFI02 16 Mbit 3V Boot Sector Flash TSOP-48

Description

Cypress Spansion S29AL016J70TFI02 16 Mbit 3V Boot Sector Flash TSOP-48
The S29AL016J is a 16 Mbit, 3.0 Volt-only Flash memory organized as 2,097,152 bytes or 1,048,576 words. The device is offered in 48-ball Fine-pitch BGA (0.8 mm pitch), 64-ball Fortified BGA (1.0 mm pitch) and 48-pin TSOP packages. The word-wide data (x16) appears on DQ15–DQ0; the byte-wide (x8) data appears on DQ7–DQ0. This device is designed to be programmed in-system with the standard system 3.0 volt VCC supply. A 12.0 V VPP or 5.0 VCC are not required for write or erase operations. The device can also be programmed in standard EPROM programmers. The device offers access time of 55 ns allowing high speed microprocessors to operate without wait states. To eliminate bus contention the device has separate chip enable (CE#), write enable (WE#) and output enable (OE#) controls. The device requires only a single 3.0 volt power supply for both read and write functions. Internally generated and regulated voltages are provided for the program and erase operations. The S29AL016J is entirely command set compatible with the JEDEC single-power-supply Flash standard. Commands are written to the command register using standard microprocessor write timings. Register contents serve as input to an internal state-machine that controls the erase and programming circuitry. Write cycles also internally latch addresses and data needed for the programming and erase operations. Reading data out of the device is similar to reading from other Flash or EPROM devices. Device programming occurs by executing the program command sequence. This initiates the Embedded Program algorithm—an internal algorithm that automatically times the program pulse widths and verifies proper cell margin. The Unlock Bypass mode facilitates faster programming times by requiring only two write cycles to program data instead of four. Device erasure occurs by executing the erase command sequence. This initiates the Embedded Erase algorithm—an internal algorithm that automatically preprograms the array (if it is not already programmed) before executing the erase operation. During erase, the device automatically times the erase pulse widths and verifies proper cell margin. The host system can detect whether a program or erase operation is complete by observing the RY/BY# pin, or by reading the DQ7 (Data# Polling) and DQ6 (toggle) status bits. After a program or erase cycle has been completed, the device is ready to read array data or accept another command. The sector erase architecture allows memory sectors to be erased and reprogrammed without affecting the data contents of other sectors. The device is fully erased when shipped from the factory. Hardware data protection measures include a low VCC detector that automatically inhibits write operations during power transitions. The hardware sector protection feature disables both program and erase operations in any combination of the sectors of memory. This can be achieved in-system or via programming equipment. The Erase Suspend/Erase Resume feature enables the user to put erase on hold for any period of time to read data from, or program data to, any sector that is not selected for erasure. True background erase can thus be achieved. The hardware RESET# pin terminates any operation in progress and resets the internal state machine to reading array data. The RESET# pin may be tied to the system reset circuitry. A system reset would thus also reset the device, enabling the system microprocessor to read the boot-up firmware from the Flash memory. The device offers two power-saving features. When addresses have been stable for a specified amount of time, the device enters the automatic sleep mode. The system can also place the device into the standby mode. Power consumption is greatly reduced in both these modes. Cypress combines years of flash memory manufacturing experience to produce the highest levels of quality, reliability and cost effectiveness. The device electrically erases all bits within a sector simultaneously via Fowler-Nordheim tunneling. The data is programmed using hot electron injection.
SPECIFICATIONS
Manufacturer: Cypress Spansion
Part Number: S29AL016J70TFI02
Product Category: NOR Flash
Mounting Style: SMD/SMT
Package / Case: TSOP-48
Series: S29AL016J
Memory Size: 16 Mbit
Supply Voltage - Min: 2.7 V
Supply Voltage - Max: 3.6 V
Active Read Current - Max: 12 mA
Interface Type: Parallel
Organization: 2 M x 8/1 M x 16
Data Bus Width: 8 bit/16 bit
Timing Type: Asynchronous
Minimum Operating Temperature: - 40 C
Maximum Operating Temperature: + 85 C
Memory Type: NOR
Speed: 70 ns
Architecture: Sector
Supply Current - Max: 12 mA
Moisture Sensitive: Yes
Subcategory: Memory & Data Storage
We are a
U.S. COMPANY
in business since 1995 and offer
FAST SHIPPING
, usually within 1 business day.
Our listings are for
GENUINE Items
, not cheap knock-off counterfeits.
Please view all photos for potential datasheets
and other information.
For full datasheet, please contact us.
Make sure to view the rest of our auctions for other
Electronic Components and Unique Electronic Devices
we have created.
Click on
Save This Seller
and get notified of Sales and New Product Listings.
If you want to purchase more quantity than listed or don't see the exact item you are searching for, please ask, we are here to help you.  We offer a discount on multiple item purchases and / or large quantities.